First-Aid Kits for Circuit Boards ®
Newsletter | Ordering | Login
Phone: 978-373-1600
  
Alternative to Dead Bug Rework More Features
This is an example of a project where the solution was more reliable, less labor intensive and much more elegant that the alternative... dead bugging.

If you're not familiar with dead bugging it's when you need to add components to a circuit board and have no place to put them so you glue them upside-down and run jumper wires to complete the circuits. It's usually a big mess.

A military contractor had an engineering change to implement to a batch of circuit board that involves the addition of 16 components. The original solution was to dead-bug the components and adding 30 jumper wires to some lifted  component  leads and surface pads.

Alternative to Dead Bug Rework
Figure 1 - Typical dead bug rework, a big mess.
We were asked if we could improve upon the fix. As always the need was urgent and there was not the available time to re-spin the artwork and fabricate new boards.

In addition to the immediate need for the 25 or so assembled boards there was a large quantity of bare boards at the contract manufacturer held up awaiting a solution.

After reviewing the project, we proposed bonding new copper conductor foil patterns directly to the board surface. Components could then be soldered to the new copper foil patterns at locations designed for each component. This method would also significantly reduce the need for jumper wires. See Figure 2.

Alternative to Dead Bug Rework
Figure 2 - New copper foil patterns prior to trimming and bonding to the circuit board surface. Two complete patterns are shown.
For this project the accuracy and placement of the new conductor patterns was critical because these were bare circuit boards and the contract manufacturer wanted to run the bare boards through their normal stencil printing, placement and reflow process.

To ensure accuracy we first milled away solder mask from the area where the new patterns would be bonded using a milling machine and carbide end mills.

Figure 3 shows removal of solder mask from the circuit board surface.

Alternative to Dead Bug Rework
Figure 3 - Light areas show where solder mask was removed by milling.
Next the new copper foil patterns were trimmed, positioned using a fiducial reference and bonded in place using heat and pressure. The copper foil patterns have a dry-film adhesive backing and are designed precisely for this type of application.

This dry-film adhesive bonding method is a common IPC recommended method for replacing damaged surface mount and BGA pads.

Figure 4 shows the new copper patterns bonded to the circuit board surface.

In this case the final steps were completed by the contractor when they ran the bare circuit boards through their normal assembly process.

Alternative to Dead Bug Rework
Figure 4 - New copper patterns bonded to the circuit board surface
A hearty handshake and pat on the back go to Dale Eckert-Granger and Nick Arivella, two senior technicians at Circuit Technology Center for their pioneering work on this project. They have a combined 48+ years of circuit board repair and rework experience that is truly unmatched.
Several members of the Circuit Technology Center team contributed to this feature story.
Are Your BGA Rework Techs Competent?
Are Your BGA Rework Techs Competent?
Can every operator handle your BGA rework equally well? In real life, in all but just a few situations, the answer is no. Why is this so?
Learn more ...
11 Rules for Circuit Board Mods
11 Rules for Circuit Board Mods
Some of the odd twists and turns occasionally needed to modify assembled circuit boards can be surprising. Discover the 11 rules your techs should know.
Learn more ...
Must Have Circuit Boards First-aid Kits
Must Have Circuit Boards First-aid Kits
These kits have been used for decades by the most demanding electronics manufacturers. Every item is thoroughly field tested.
Learn more ...
Can You Repair a Broken Corner?
Can You Repair a Broken Corner?
What happens to an assembled circuit board with a broken corner? Can it be repaired reliably? It can if you have the training and the experience.
Learn more ...
Challenging Surface Mount Pad Repair
Challenging Surface Mount Pad Repair
Surface mount and BGA pad repair are routine operations at Circuit Technology Center. Learn how it's done with absolute precision and reliably.
Learn more ...
Do Your Repair Techs Deserve One?
Do Your Repair Techs Deserve One?
The Micro-Drill is the ideal tool for precision drilling, grinding and cutting on circuit boards. Use it to remove coatings, cuts circuits, drills holes, and much more.
Learn more ...
87 Repair/Rework Guides Free Online
87 Repair/Rework Guides Free Online
This free online guidebook, packed with detailed illustrations, will be helpful to anyone who needs to repair or rework circuit board assemblies.
Learn more ...
BGA Component Rework Simplified
BGA Component Rework Simplified
When you have tough BGA rework, where do you turn to? Discover the nation's #1 contractor for outsourced BGA rework, repair and reballing.
Learn more ...
Stop PCB Scrap Today
Stop PCB Scrap Today
What happens to your valuable circuit boards when they're damaged? Can they be repaired reliably and cost-effectively? Yes, if you have the skills and knowhow.
Learn more ...