First-Aid Kits for Circuit Boards ®
Newsletter | Ordering | Login
Phone: 978-373-1600
  
Challenging Connector Rework More Features
Challenging Connector Rework
Image 2. Wires surrounding the connector solder joints.
Challenging Connector Rework
Image 1. Connectors that require removal and replacement.
A major manufacturer was looking to remove and replace five 170 pin through hole connectors on several multi-layer backplane circuit boards. Naturally there was a need to avoid burning the base board surface or damaging to the plated holes. This was a challenging task. See image 1.

Due to the many power and ground planes, the heating process needed to achieve reflow was complex. The challenge was further complicated due to the need to avoid overheating the many jumpers wires adjacent the connector sites.

Challenging Connector Rework
Image 3. Site prepared using heat shield materials.
Normally you might first remove the wires, but that step would have added significantly to the rework process time so the wires needed to remain in place during the reflow process. See image 2.

The first step involved protecting the heat sensitive areas and base board. This was done with a combination of heat shield blankets, heat shield plates and heat shield mask. These components were encased in an additional layer of high temperature tape. See image 3.

With the prep steps completed, the connectors were reliably removed using a solder fountain system. After the connector removal, each plated hole was cleared of the residual solder using a vacuum desoldering system.

Challenging Connector Rework
Image 4. Connector removed ready for hole clearing.
Installation of the replacement connectors was also completed using the solder fountain system. Key to this project was the use of the heat shielding materials used to protect the circuit board surface, and especially the adjacent wires.

You can learn about the heat shield materials at:
http://www.circuitmedic.com/products/201-3160.shtml
Several members of the Circuit Technology Center team contributed to this feature story.
Are Your BGA Rework Techs Competent?
Are Your BGA Rework Techs Competent?
Can every operator handle your BGA rework equally well? In real life, in all but just a few situations, the answer is no. Why is this so?
Learn more ...
11 Rules for Circuit Board Mods
11 Rules for Circuit Board Mods
Some of the odd twists and turns occasionally needed to modify assembled circuit boards can be surprising. Discover the 11 rules your techs should know.
Learn more ...
Must Have Circuit Boards First-aid Kits
Must Have Circuit Boards First-aid Kits
These kits have been used for decades by the most demanding electronics manufacturers. Every item is thoroughly field tested.
Learn more ...
Can You Repair a Broken Corner?
Can You Repair a Broken Corner?
What happens to an assembled circuit board with a broken corner? Can it be repaired reliably? It can if you have the training and the experience.
Learn more ...
Challenging Surface Mount Pad Repair
Challenging Surface Mount Pad Repair
Surface mount and BGA pad repair are routine operations at Circuit Technology Center. Learn how it's done with absolute precision and reliably.
Learn more ...
Do Your Repair Techs Deserve One?
Do Your Repair Techs Deserve One?
The Micro-Drill is the ideal tool for precision drilling, grinding and cutting on circuit boards. Use it to remove coatings, cuts circuits, drills holes, and much more.
Learn more ...
87 Repair/Rework Guides Free Online
87 Repair/Rework Guides Free Online
This free online guidebook, packed with detailed illustrations, will be helpful to anyone who needs to repair or rework circuit board assemblies.
Learn more ...
BGA Component Rework Simplified
BGA Component Rework Simplified
When you have tough BGA rework, where do you turn to? Discover the nation's #1 contractor for outsourced BGA rework, repair and reballing.
Learn more ...
Stop PCB Scrap Today
Stop PCB Scrap Today
What happens to your valuable circuit boards when they're damaged? Can they be repaired reliably and cost-effectively? Yes, if you have the skills and knowhow.
Learn more ...