First-Aid Kits for Circuit Boards ®
Newsletter | Ordering | Login
Phone: 978-373-1600
  

2.1 Handling Electronic Assemblies

Outline
This procedure covers the proper methods for handling circuit boards.

Minimum Skill Level - Intermediate
Recommended for technicians with skills in basic soldering and component rework, but may be inexperienced in general repair/rework procedures.

Conformance Level - High
This procedure most closely duplicates the physical characteristics of the original, and most probably complies with all the functional, environmental and serviceability factors.

Acceptability References
IPC-A-610 3.0 Handling Electronic Assemblies
Procedure References
1.0 Foreword
IPC 7721 2.1 Handling Electronic Assemblies
Images and Figures
2.1 Handling Electronic Assemblies
Figure 1: Always handle circuit boards by the edges.
Electrostatic Discharge (ESD)
Certain components used in electronic assemblies are sensitive to static electricity and can be damaged by its discharge. Static charges are created when non-conductive materials are separated, such as when plastic bags are picked up or opened, when friction occurs between articles of synthetic clothing, when plastic tapes are dispensed and many other causes.

Destructive static charges are induced on nearby conductors, such as human skin, and delivered in the form of sparks passing between conductors, such as when the surface of printed board assembly is touched by a person having a static charge potential. If touched at the right solder joint or conductive pattern, the circuit board assembly can be damaged as the discharge passes through the conductive pattern to a static sensitive component. It is important to note that usually the static damage level for components cannot be felt by humans. (Less than 3,000 volts.)

Electrical Overstress (EOS)
Electrical overstress damage can be caused by generation of unwanted energy; such as spikes, occurring within soldering irons, solder extractors, testing instruments and other electrically operated equipment. This equipment must be designed as to prevent unwanted electrical discharges.

ESD/EOS Safe Work Areas
The purpose of an ESD/EOS safe work area is to prevent damage to sensitive components from spikes and static discharges. These areas must be designed and maintained to prevent ESD/EOS damage.

Handling and Storage Methods
  1. Circuit board assemblies must always be handled at properly designated work areas.
  2. Designated work areas must be checked periodically to ensure their continued protection. Areas of main concern include:
    1. Proper grounding methods.
    2. Static dissipation of work surfaces.
    3. Static dissipation of floor surfaces.
    4. Operation of ion blowers and ion air guns.
  3. Designated work areas must be kept free of static generating materials including Styrofoam, vinyl, plastic, fabrics and other static generating materials.
  4. Work areas must be kept clean and neat. To prevent contamination of circuit board assemblies, there must be no eating or smoking in the work area.
  5. When not being worked on, sensitive components and circuit boards must be enclosed in shielded bags or boxes. There are three types of ESD protective enclosure materials including:
    Static Shielding - Prevents static electricity from passing through the package.
    Antistatic - Provides antistatic cushioning for electronic assemblies.
    Static Dissipative - An "over-package" that has enough conductivity to dissipate any static buildup.
  6. Whenever handling a circuit board assembly the operator must be properly grounded by one of the following:
    1. Wearing a wrist strap connected to earth ground.
    2. Wearing 2 heel grounders and have both feet on a static dissipative floor surface.
  7. Circuit board assemblies should be handled by the edges. Avoid touching the circuits or components. (See Figure 1)
  8. Components should be handled by the edges when possible. Avoid touching the component leads.
  9. Hand creams and lotions containing silicone must not be used since they can cause solderability and epoxy adhesion problems. Lotions specifically formulated to prevent contamination of circuit boards are available.
  10. Stacking of circuit boards and assemblies should be avoided to prevent physical damage. Special racks and trays are available for handling.
Procedure for reference only.
Questions?
Call 978-374-5000 or submit your question using the form below.

Your Name


Your Company


Your E-mail


Your Country


Your Phone


Questions



Keep This Plated-Hole Repair Kit Handy
Keep This Plated-Hole Repair Kit Handy
Plated holes in circuit boards are easily damaged. This kit includes all the tools and materials needed to repair damaged plated through holes.
Learn more ...
Are Your BGA Rework Techs Experts?
Are Your BGA Rework Techs Experts?
Can every operator handle your BGA rework equally well? In real life, in all but just a few situations, the answer is no. Why is this so?
Learn more ...
Jumper Wire Hassles Eliminated
Jumper Wire Hassles Eliminated
Throw away that super glue and eliminate that super glue mess. Clean up your act when bonding wires. Wire Dots make the job clean, neat and fast.
Learn more ...
11 Rules for Circuit Board Mods
11 Rules for Circuit Board Mods
Some of the odd twists and turns occasionally needed to modify assembled circuit boards can be surprising. Discover the 11 rules your techs should know.
Learn more ...
ipc-logo Circuit Technology Center has been an IPC member since 1986
Circuit Technology Center Logo
Surgeon grade rework and repair,
by the book and guaranteed. ®