First-Aid Kits for Circuit Boards ®
Newsletter | Ordering | Login
Phone: 978-373-1600
  

2.3.3 Coating Removal, Peeling Method

  • This peeling removal method for coating can be used only under special circumstances. Normally this method is used to remove RTV silicone or other thick rubbery-like coating materials.
  • Slit and peel off the coating material with a dull knife or heated dull blade. Repeat as needed until the required material is removed.
  • Image shows coating removal completed.
Outline
This peeling removal method for coating can be used only under special circumstances. Normally this method is used to remove RTV silicone or other thick rubbery-like coating materials.

The coating material is removed using a dull knife or otherwise dull blade to slit the coating material and to peel it off the printed board or printed board assembly.

To determine the appropriate coating removal procedure the coating must first be identified. Refer to procedure number 2.3.1.

Note
This method is limited to coatings that are rubbery in nature to allow the coating material to be slit into small sections and peeled off the printed board assembly.

Proprietary Information Proprietary
This guide may contain proprietary or copyright-protected information for access by authorized persons only.

Minimum Skill Level - Advanced
Recommended for technicians with soldering and component rework skills and exposure to most repair/rework procedures, but lacking extensive experience.

Conformance Level - High
This procedure most closely duplicates the physical characteristics of the original, and most probably complies with all the functional, environmental and serviceability factors.

Acceptability References
IPC-A-600 2.0 Externally Observable Characteristics  Proprietary
IPC-A-610 10.0 Laminate Conditions  Proprietary
Procedure References
1.0 Foreword
2.1 Handling Electronic Assemblies
2.2 Cleaning
2.3.1 Coating Removal, Identification Of Coatings
2.4.1 Coating Replacement, Solder Mask
2.4.2 Coating Replacement, Conformal Coatings/Encapsulants
IPC 7721 3.3 Coating Removal, Peeling Method  Proprietary
Tools and Materials
CircuitMedic Part
Knife with #16 Blades
A must-have tool for precise cutting, scraping and trimming.
CircuitMedic Part
Mixing Picks
Unique mixing sticks have a paddle shape on one and sharp pick on the opposite end.
Thermal Tool
Thermal Parting Tool
Thermal removal tool using controlled heat through specially shaped tips.
Images and Figures
2.3.3 Coating Removal, Peeling Method
Coating Removal Required At Outlined Area
2.3.3 Coating Removal, Peeling Method
Figure 1: Slit and peel off coating using a knife or heated blade.
2.3.3 Coating Removal, Peeling Method
Figure 2: Removal complete.

Procedure
  1. Slit and peel off the coating material with a dull knife or heated dull blade. (See Figure 1)
  2. Repeat as needed until the required material is removed.
Evaluation
  1. Visual examination or UV light may be used to verify complete removal of coating.
Procedure for reference only.
Questions?
Call 978-374-5000 or submit your question using the form below.

Your Name


Your Company


Your E-mail


Your Country


Your Phone


Questions



Keep This Plated-Hole Kit Handy
Keep This Plated-Hole Kit Handy
Plated holes in circuit boards are easily damaged. This kit includes all the tools and materials needed to repair damaged plated through holes.
Learn more ...
Are Your BGA Rework Techs Experts?
Are Your BGA Rework Techs Experts?
Can every operator handle your BGA rework equally well? In real life, in all but just a few situations, the answer is no. Why is this so?
Learn more ...
Jumper Wire Hassles Eliminated
Jumper Wire Hassles Eliminated
Throw away that super glue and eliminate that super glue mess. Clean up your act when bonding wires. Wire Dots make the job clean, neat and fast.
Learn more ...
11 Rules for Circuit Board Mods
11 Rules for Circuit Board Mods
Some of the odd twists occasionally needed to modify assembled circuit boards can be surprising. Discover the 11 rules your techs should know.
Learn more ...
ipc-logo Circuit Technology Center has been an IPC member since 1986
Circuit Technology Center Logo
Surgeon grade rework and repair,
by the book and guaranteed. ®