First-Aid Kits for Circuit Boards ®
Newsletter | Ordering | Login
Phone: 978-373-1600
  

2.6.1 Legend/Marking, Stamping Method

  • This method can be used to add, change or replace legend and markings on printed boards or printed board assemblies. This method uses epoxy ink and an ink stamp to place the legends on the printed board surface in much the same manner as taking a "finger print".
  • You select the appropriate characters from a peg stamp set, or have a special stamp fabricated. You then mix the epoxy ink, white is the most common color. You spread a thin even coating of the epoxy ink on a smooth surface. Gently press the peg stamp into the epoxy and transfer it onto the circuit board surface.
  • As required cure the epoxy ink per the manufacturer's instructions.
Outline
This method can be used to add, change or replace legend and markings on printed boards or printed board assemblies. This method uses epoxy ink and an ink stamp to place the legends on the printed board surface in much the same manner as taking a "finger print".

Proprietary Information Proprietary
This guide may contain proprietary or copyright-protected information for access by authorized persons only.

Minimum Skill Level - Intermediate
Recommended for technicians with skills in basic soldering and component rework, but may be inexperienced in general repair/rework procedures.

Conformance Level - High
This procedure most closely duplicates the physical characteristics of the original, and most probably complies with all the functional, environmental and serviceability factors.

Acceptability References
IPC-A-600 2.0 Externally Observable Characteristics  Proprietary
IPC-A-610 8.0 Marking  Proprietary
Procedure References
1.0 Foreword
2.1 Handling Electronic Assemblies
2.2 Cleaning
2.5 Baking And Preheating
2.7 Epoxy Mixing and Handling
IPC7721 2.6.1 Legend/Marking, Stamping Method  Proprietary
Tools and Materials
CircuitMedic Part
Alcohol Swab
Self-saturating Isopropyl alcohol swab. Squeeze handle to release alcohol.
Cleaner
Cleaner
General purpose cleaner for removing contamination.
CircuitMedic Part
Cleaning Brushes
Disposable brushes for use with solvents for cleaning and application of coatings.
Coatings
Color Agents
Use to tint the color of epoxy used for solder mask repair or circuit base board repair.
CircuitMedic Part
Circuit Bond Packs
Clear, superior strength epoxy in two-compartment plastic packages
CircuitMedic Part
Knife with #16 Blades
A must-have tool for precise cutting, scraping and trimming.
Microscope
Microscope
Precision microscope with stand and lighting for work and inspection.
Oven
Oven
General purpose oven for drying, baking and curing epoxies.
Peg Stamps
Peg Stamps
Peg stamps for application of inks to replace text and markings.
Wipes
Wipes
Nonabrasive, low-linting wipes for cleanup.
Images and Figures
2.6.1  Legend/Marking, Stamping Method
Damaged Legend
2.6.1  Legend/Marking, Stamping Method
Figure 1: Apply legend using a peg stamp.
2.6.1  Legend/Marking, Stamping Method
Figure 2: Completed legend repair.

Procedure
  1. Clean the area.
  2. Scrape off any remaining character or legend with a knife and clean the area.

    Caution
    Abrasion operations can generate electrostatic charges.
  3. Select the appropriate characters from the peg stamp set or have a special stamp made up.
  4. Mix the epoxy ink. White is the most common color. Spread a thin even coating of the epoxy ink on the ink plate or on a smooth surface.
  5. Gently press the peg stamp into the epoxy coating to coat the character surface.
  6. Gently press the peg stamp onto the desired location on the circuit board surface. (See Figure 1)
  7. Cure the epoxy ink per the manufacturer's instructions.
Evaluation
  1. Visual examination for proper characters, positioning and legibility.
Procedure for reference only.
 

Related Products

115-1322 Circuit Bond Kit
Kit containing packages of clear, low viscosity, superior strength epoxy for circuit board damage repair.
Color Agents
One part, air-drying, semi-paste ink for printing on hard surfaces and used to tint the color of epoxy.
Questions?
Call 978-374-5000 or submit your question using the form below.

Your Name


Your Company


Your E-mail


Your Country


Your Phone


Questions



A Simple Fix for Damaged Conductors
A Simple Fix for Damaged Conductors
There is a quick and reliable IPC recommended repair for damaged conductors. The replacement conductor matches the original. Discover the secret.
Learn more ...
Tough Engineering Changes?
Tough Engineering Changes?
Engineering changes are a reality that need to be dealt with. Do you have qualified rework technicians to do the job efficiently and reliably?
Learn more ...
Epoxy Packs Eliminate Measuring
Epoxy Packs Eliminate Measuring
This unique kit contains 10 packages of super strength epoxy, precisely measured out into two-compartment plastic packages.
Learn more ...
87 Repair/Rework Guides Free Online
87 Repair/Rework Guides Free Online
This free online guidebook, packed with detailed illustrations, will be helpful to anyone who needs to repair or rework circuit board assemblies.
Learn more ...
ipc-logo Circuit Technology Center has been an IPC member since 1986
Circuit Technology Center Logo
Surgeon grade rework and repair,
by the book and guaranteed. ®