First-Aid Kits for Circuit Boards ®
Newsletter | Ordering | Login
Phone: 978-373-1600
  

3.3.1 Hole Repair, Epoxy Method

  • This method is used to repair cosmetic defects or minor damage to an unsupported tooling or mounting hole.
  • Mill away damaged material with the Micro-Drill and ball mill.
  • A powered Micro-Drill is the ideal tool for precision grinding of circuit board materials.
  • Apply epoxy with a mixing stick sharpened at one end.
Outline
This method is used to repair cosmetic defects or minor damage to an unsupported tooling or mounting hole. The hole may have component leads, wires, fasteners, pins, terminals or other hardware run through it. This repair method uses high strength epoxy to restore the damaged surface surrounding the hole. This method can be used on single sided, double sided or multilayer circuit boards and assemblies.

Caution
Damaged inner-layer connections may require surface wire adds.

Minimum Skill Level - Advanced
Recommended for technicians with soldering and component rework skills and exposure to most repair/rework procedures, but lacking extensive experience.

Conformance Level - High
This procedure most closely duplicates the physical characteristics of the original, and most probably complies with all the functional, environmental and serviceability factors.

Acceptability References
IPC-A-600 2.0 Externally Observable Characteristics
IPC-A-610 10.0 Laminate Conditions
Procedure References
1.0 Foreword
2.1 Handling Electronic Assemblies
2.2 Cleaning
2.5 Baking And Preheating
2.7 Epoxy Mixing and Handling
IPC7721 3.3.1 Hole Repair, Epoxy Method
Tools and Materials
CircuitMedic Part
Alcohol Swab
Self-saturating Isopropyl alcohol swab. Squeeze handle to release alcohol.
CircuitMedic Part
Ball Mills, Abrasives, Cutting Tools
Ball mills, abrasives and cutting tools for working on circuit boards.
CircuitMedic Part
Cleaning Brushes
Disposable brushes for use with solvents for cleaning and application of coatings.
CircuitMedic Part
Circuit Bond Packs
Clear, superior strength epoxy in two-compartment plastic packages
CircuitMedic Part
High Temp Tape Discs
High temperature polyimide tape discs, .50" diameter.
CircuitMedic Part
Knife with #16 Blades
A must-have tool for precise cutting, scraping and trimming.
CircuitMedic Part
Micro Drill System
Versatile power tool for milling, drilling, grinding, cutting and sanding circuit boards.
CircuitMedic Part
Scraper
Hardened stainless steel tip for scraping solder mask and removing defects.
Images and Figures
3.3.1 Hole Repair, Epoxy Method
Damaged hole, non plated.
3.3.1 Hole Repair, Epoxy Method
Figure 1: Mill away damaged material with the Micro-Drill and ball mill.
3.3.1 Hole Repair, Epoxy Method
Figure 2: Apply epoxy with a mixing stick sharpened at one end.

3.3.1 Hole Repair, Epoxy Method
Figure 3: Micro-Drill System.
Procedure
  1. Clean the area.
  2. Mill away the damaged board base material using the Micro-Drill and ball mill. All damaged base board material and solder mask must be removed. No fibers of laminate material should be exposed at the surface perimeter of the hole. (See Figure 1)

    Note
    To clearly see that all damaged material has been removed, flood the area with alcohol or solvent. Damaged internal fibers of the base material will show up clearly.
  3. Remove all loose material and clean the area.
  4. Where needed, apply High Temperature Tape to protect exposed parts of the circuit board. Tape may be required inside the hole. If epoxy reduces the inside diameter, the hole may have to be re-drilled after the epoxy has cured.

    Note
    The circuit board may be preheated prior to filling the area with epoxy. A preheated circuit board will allow the epoxy to easily flow and level out. Epoxy applied to an unheated circuit board may settle below the circuit board surface as the epoxy cures.

    Caution
    Some components may be sensitive to high temperatures.
  5. Mix the epoxy. If desired, add color agent to the mixed epoxy to match the circuit board color.
  6. Coat the area with epoxy up to and flush with the circuit board surface. A mixing stick may be used to apply and spread the epoxy.

    Note
    A slight overfill of epoxy may be desired to allow for shrinkage when epoxy cures.
  7. Cure the epoxy per Procedure 2.7 Epoxy Mixing and Handling.
  8. After the epoxy has cured, remove the tape.
  9. If needed, use a knife or scraper and scrape off any excess epoxy. Scrape until the new epoxy surface is level with the surrounding circuit board surface.

    Note
    Apply surface coating to match prior coating as required.
  10. Remove all loose material. Clean the area.
Procedure for reference only.
 

Related Products

115-1322 Circuit Bond Kit
Kit containing packages of clear, low viscosity, superior strength epoxy for circuit board damage repair.
201-3110 Base Board Repair Kit
Kit to repair base board and laminate damage on circuit boards.
Color Agents
One part, air-drying, semi-paste ink for printing on hard surfaces and used to tint the color of epoxy.
110-4105 Micro Drill System
Versatile power tool for milling, drilling, grinding, cutting and sanding circuit boards.
The Toughest Component Rework?
The Toughest Component Rework?
Rework of surface mount and through hole components can be a challenge. Our techs are ready to tackle your toughest rework projects.
Learn more ...
Challenging Surface Mount Pad Repair
Challenging Surface Mount Pad Repair
Surface mount and BGA pad repair are routine operations at Circuit Technology Center. Learn how it's done with absolute precision and reliably.
Learn more ...
BGA Component Rework Simplified
BGA Component Rework Simplified
When you have tough BGA rework, where do you turn to? Discover the nation's #1 contractor for outsourced BGA rework, repair and reballing.
Learn more ...
Can You Repair a Broken Corner?
Can You Repair a Broken Corner?
What happens to an assembled circuit board with a broken corner? Can it be repaired reliably? It can if you have the training and the experience.
Learn more ...
ipc-logo Circuit Technology Center has been an IPC member since 1986
Circuit Technology Center Logo
Surgeon grade rework and repair,
by the book and guaranteed. ®