First-Aid Kits for Circuit Boards ®
Newsletter | Ordering | Login
Phone: 978-373-1600
  

4.2.3 Conductor Repair, Welding Method

Outline
This procedure is used to repair short breaks or opens in circuits on circuit boards. A parallel gap welder is used to weld a jumper ribbon across the damaged conductor.

Caution
Welding current and voltages may affect component reliability on assembled circuit boards. The repaired section must not reduce the circuit width, spacings or current carrying capacity below the allowable tolerances.

Caution
Sub miniature parallel gap welding is extremely sensitive to proper placement of the electrode tip. Inconsistent welds can occur due to poor electrode tip placement, incorrect tip size, or improper weld settings.

Preparation
Prior to using any welding equipment, certain precautions should be taken. The equipment should have electrodes cleaned, aligned and set for the proper board thickness.

Test samples that have similar circuit widths, spacing, thickness, surface finish, contour, etc. Observe and test the weld quality, alignment, discoloration, fusion and the appearance of the base material in the area of the weld. Readjust the weld equipment settings and repeat until acceptable results have been achieved.

The alignment of the welded ribbon to the circuit pattern should be within 0.050 mm (.002"). The weld bond strength should exceed the circuit/base material bond strength.

Minimum Skill Level - Advanced
Recommended for technicians with soldering and component rework skills and exposure to most repair/rework procedures, but lacking extensive experience.

Conformance Level - High
This procedure most closely duplicates the physical characteristics of the original, and most probably complies with all the functional, environmental and serviceability factors.

Acceptability References
IPC-A-600 2.0 Externally Observable Characteristics
IPC-A-610 10.0 Laminate Conditions
Procedure References
1.0 Foreword
2.1 Handling Electronic Assemblies
2.2 Cleaning
2.7 Epoxy Mixing and Handling
IPC7721 4.2.3 Conductor Repair, Welding Method
Tools and Materials
CircuitMedic Part
Abrader
Mild abrasive for removing oxides and contaminates from conductive surfaces.
CircuitMedic Part
Alcohol Swab
Self-saturating Isopropyl alcohol swab. Squeeze handle to release alcohol.
Cleaner
Cleaner
General purpose cleaner for removing contamination.
CircuitMedic Part
Cleaning Brushes
Disposable brushes for use with solvents for cleaning and application of coatings.
CircuitMedic Part
Circuit Bond Packs
Clear, superior strength epoxy in two-compartment plastic packages
CircuitMedic Part
Knife with #16 Blades
A must-have tool for precise cutting, scraping and trimming.
Solderinmg Iron
Soldering Iron, Solder and Flux
Properly maintained soldering iron, soldering iron tips, solder and flux.
CircuitMedic Part
Tweezer, Point Tip
Fine point tweezers for precision work.
Wipes
Wipes
Nonabrasive, low-linting wipes for cleanup.
Proprietary Information
This procedure contains proprietary information. The information is in a password protected folder for access by Circuit Technology Center, Inc. employees only.
Procedure
  1. Clean the area.
  2. Select a section of Kovar ribbon of the same width as the conductor pattern being repaired +/- .050 mm - 0.002".
  3. Cut the ribbon approximately 3.0 mm (.120") longer than the section being repaired.
  4. Clean the ribbon conductor and base material surrounding the repair area.
  5. Place and center the ribbon over the section to be repaired leaving equal ribbon end lengths on each side and parallel to the circuit pattern.
  6. Place the circuit board under the weld electrodes so that the electrodes are depressed to the area of the weld.
  7. Hold the ribbon in place with the Precision Tweezers until the weld is completed. Weld in place using settings based on the accepted test samples.
  8. Clean the area.
  9. Carefully inspect the joint for weld quality and alignment.
  10. If required, apply a small amount of flux and tin the entire area with solder.
  11. Clean the area.
  12. Coat the repaired area with epoxy if needed.
Evaluation
  1. Visual examination, dimensional measurement of conductor width and spacing, and electrical continuity measurement.
Procedure for reference only.
Questions?
Call 978-374-5000 or submit your question using the form below.

Your Name


Your Company


Your E-mail


Your Country


Your Phone


Questions



Do Your Repair Techs Deserve One?
Do Your Repair Techs Deserve One?
The Micro-Drill is the ideal tool for precision drilling, grinding and cutting on circuit boards. Use it to remove coatings, cuts circuits, drills holes, and much more.
Learn more ...
Discover 3 Options for BGA Rework
Discover 3 Options for BGA Rework
No matter how much we attempt to streamline and automate the process, BGA Rework has been, and will likely always be, a mixture of art and science.
Learn more ...
Must Have Circuit Boards First-aid Kits
Must Have Circuit Boards First-aid Kits
These kits have been used for decades by the most demanding electronics manufacturers. Every item is thoroughly field tested.
Learn more ...
Stop PCB Scrap Today
Stop PCB Scrap Today
What happens to your valuable circuit boards when they're damaged? Can they be repaired reliably and cost-effectively? Yes, if you have the skills and knowhow.
Learn more ...
ipc-logo Circuit Technology Center has been an IPC member since 1986
Circuit Technology Center Logo
Surgeon grade rework and repair,
by the book and guaranteed. ®