First-Aid Kits for Circuit Boards ®
Newsletter | Ordering | Login
Phone: 978-373-1600
  

4.4.1 Lifted Land Repair, Epoxy Seal Method

  • This method is used to rebond a lifted land.
  • Carefully apply a small amount of epoxy under the entire length of the lifted land.
  • Place high temperature tape over the lifted land.
  • Completed repair.
Outline
This method is used to rebond a lifted land. Liquid epoxy is inserted under and around the land to bond it back down to the circuit board surface.

Minimum Skill Level - Advanced
Recommended for technicians with soldering and component rework skills and exposure to most repair/rework procedures, but lacking extensive experience.

Conformance Level - Medium
This procedure may have some variance with the physical character of the original and most likely varies with some of the functional, environmental and serviceability factors.

Acceptability References
IPC-A-600 2.0 Externally Observable Characteristics
IPC-A-610 10.0 Laminate Conditions
Procedure References
1.0 Foreword
2.1 Handling Electronic Assemblies
2.2 Cleaning
2.5 Baking And Preheating
2.7 Epoxy Mixing and Handling
IPC7721 4.4.1 Lifted Land Repair, Epoxy Method
Tools and Materials
CircuitMedic Part
Circuit Bond Packs
Clear, superior strength epoxy in two-compartment plastic packages
CircuitMedic Part
High Temp Tape Discs
High temperature polyimide tape discs, .50" diameter.
CircuitMedic Part
Knife with #16 Blades
A must-have tool for precise cutting, scraping and trimming.
CircuitMedic Part
Scraper
Hardened stainless steel tip for scraping solder mask and removing defects.
Images and Figures
4.4.1 Lifted Land Repair, Epoxy Seal Method
Lifted Land.
4.4.1 Lifted Land Repair, Epoxy Seal Method
Figure 1: Carefully apply a small amount of epoxy under the entire length of the lifted land.
4.4.1 Lifted Land Repair, Epoxy Seal Method
Figure 2: Place high temperature tape over the lifted land.

4.4.1 Lifted Land Repair, Epoxy Seal Method
Figure 3: Completed repair.
Procedure
  1. Clean the area.
  2. Remove any obstructions that prevent the lifted land from making contact with the base board surface.

    Caution
    Be careful while cleaning and removing all obstructions, not to stretch or damage the lifted land.
  3. Mix the epoxy.

  4. Carefully apply a small amount of epoxy under the entire length of the lifted land. The tip of the knife or scraper may be used to apply the epoxy. (See Figure 1)
  5. Place a piece of High Temperature Tape over the lifted land and press the land down into the epoxy and into contact with the base board material. (See Figure 2)
  6. Apply additional epoxy to the surface of the lifted land and to all sides as needed.
  7. Cure the epoxy per Procedure 2.7 Epoxy Mixing and Handling.

    Caution
    Some components may be sensitive to high temperatures.

    Note
    Double sided and multilayer circuit Boards, may require an eyelet to restore the through connection. Refer to section 5.0 Plated Hole Procedures.
  8. Carefully remove any excess epoxy inside the plated hole using a ball mill or drill bit. Turn the ball mill or drill bit by hand to prevent damage to the wall of the plated through hole.
  9. Install the proper component and solder in place.

    Note
    This method is used to repair lifted lands, but the repaired lands may not have an intermetallic connection to the remaining plated hole. The solder joint of the replaced component will restore the integrity of the electrical connection or an eyelet or buss wire may be used. See Plated Hole Repair Procedures.
  10. Replace surface coating to match prior coating as required.
Evaluation
  1. Visual examination and tape test per IPC-TM-650 test method 2.4.1. (ANSI/IPC-FC-250A)
  2. Electrical tests as applicable.
Procedure for reference only.
 

Related Products

115-1322 Circuit Bond Kit
Kit containing packages of clear, low viscosity, superior strength epoxy for circuit board damage repair.
Circuit Frames
Circuit Frames for surface mount pad, BGA pad and conductor repair.
Questions?
Call 978-374-5000 or submit your question using the form below.

Your Name


Your Company


Your E-mail


Your Country


Your Phone


Questions



Keep This Plated-Hole Repair Kit Handy
Keep This Plated-Hole Repair Kit Handy
Plated holes in circuit boards are easily damaged. This kit includes all the tools and materials needed to repair damaged plated through holes.
Learn more ...
Are Your BGA Rework Techs Experts?
Are Your BGA Rework Techs Experts?
Can every operator handle your BGA rework equally well? In real life, in all but just a few situations, the answer is no. Why is this so?
Learn more ...
Jumper Wire Hassles Eliminated
Jumper Wire Hassles Eliminated
Throw away that super glue and eliminate that super glue mess. Clean up your act when bonding wires. Wire Dots make the job clean, neat and fast.
Learn more ...
11 Rules for Circuit Board Mods
11 Rules for Circuit Board Mods
Some of the odd twists and turns occasionally needed to modify assembled circuit boards can be surprising. Discover the 11 rules your techs should know.
Learn more ...
ipc-logo Circuit Technology Center has been an IPC member since 1986
Circuit Technology Center Logo
Surgeon grade rework and repair,
by the book and guaranteed. ®