First-Aid Kits for Circuit Boards ®
Newsletter | Ordering | Login
Phone: 978-373-1600
  

6.2.1 Jumper Wires, BGA Components, Circuit Track Method

Outline
This method is used to change a circuit path at a BGA site for engineering changes or modifications.

Note
This procedure requires precision milling equipment and highly trained technicians.

Caution
This procedure is not applicable for "via in pad" applications.

Minimum Skill Level - Expert
Recommended for technicians with advanced soldering and component rework skills and extensive experience in most repair/rework procedures.

Conformance Level - Medium
This procedure may have some variance with the physical character of the original and most likely varies with some of the functional, environmental and serviceability factors.

Acceptability References
IPC-A-600 2.0 Externally Observable Characteristics
IPC-A-610 11.0 Discrete Wiring
Procedure References
1.0 Foreword
2.1 Handling Electronic Assemblies
2.2 Cleaning
2.5 Baking And Preheating
2.7 Epoxy Mixing and Handling
9.0 BGA Component Rework Procedures
IPC7721 6.2.1 Jumper Wires, BGA Components, Circuit Track Method
Tools and Materials
CircuitMedic Part
Bonding Iron, 120 VAC
Delivers the optimal heat for curing adhesive bonding film.
CircuitMedic Part
Circuit Track Kit
Kit to repair circuit board damage including lands and conductors.
CircuitMedic Part
Circuit Bond Packs
Clear, superior strength epoxy in two-compartment plastic packages
CircuitMedic Part
High Temp Tape Discs
High temperature polyimide tape discs, .50" diameter.
CircuitMedic Part
Knife with #16 Blades
A must-have tool for precise cutting, scraping and trimming.
CircuitMedic Part
Scraper
Hardened stainless steel tip for scraping solder mask and removing defects.
CircuitMedic Part
Tweezer, Point Tip
Fine point tweezers for precision work.
Images and Figures
6.2.1 Jumper Wires, BGA Components, Circuit Track Method
Figure 1: Cut the connection to the via using a Precision Drill System.
6.2.1 Jumper Wires, BGA Components, Circuit Track Method
Figure 2: Remove the BGA pad and mill a shallow channel into the solder mask surface.
6.2.1 Jumper Wires, BGA Components, Circuit Track Method
Figure 3: Bond a new BGA pad in place.

6.2.1 Jumper Wires, BGA Components, Circuit Track Method
Figure 4: Solder a copper circuit track to the tail extending from the new BGA pad
6.2.1 Jumper Wires, BGA Components, Circuit Track Method
Figure 5: Solder a wire to the Circuit Track and overcoat with epoxy.
6.2.1 Jumper Wires, BGA Components, Circuit Track Method
Figure 6: Precision Drill System used to cut the connection from the BGA pad to the via.

Procedure
  1. Clean the area.
  2. Remove the BGA component if installed, remove excess solder from the pads, and clean and inspect the site using standard BGA rework equipment.
  3. Cut the short conductor (dog bone) connecting the BGA pad to the connecting via using a Precision Drill System or milling machine and appropriate size end mill. (See Figure 1 and 6)
  4. Remove the existing BGA pad. Apply heat from a soldering iron if needed. (See Figure 2)
  5. Use a milling machine to mill a shallow groove in the board surface from the BGA pad area to the perimeter of the BGA site. Tight spacing may restrict the width of the channel to 0.25 mm (.010") or less. Use a carbide end mill approximately0.050 mm (.002") wider than the new connecting circuit. (See Figure 3)
  6. Bond a replacement BGA pad in place using a bonding system. (See Procedure 4.7.3) The new BGA pad must have a tail that will align with the circuit track to be added next. (See Figure 4)
  7. Select a Circuit Track to match the width and thickness of the circuit to be replaced. Cut a length approximately as needed. The Circuit Track should overlap the BGA tail section a minimum of 2 times the circuit width.
  8. Gently abrade the top and bottom of the new Circuit Track with the buffer to remove any oxidation and clean.

    Note
    If needed, the ends of the Circuit Track may be tinned with solder prior to lap soldering in place.
  9. Position this new Circuit Track along the milled groove. The Circuit Track should overlap the existing circuit a minimum of 2 times the circuit width. (See Figure 4)
  10. Apply a small amount of liquid flux to the overlap joint.
  11. Lap solder the Circuit Track to the BGA tail section using solder and a soldering iron. Make sure the new circuit is properly aligned.
  12. Solder one end of a fine gauge wire to the end of the extending circuit. The opposite end of the wire will be soldered later. (See Figure 5)
  13. Clean the area.
  14. Mix epoxy. If desired, add color agent to the mixed epoxy to match the circuit board color.
  15. Coat the top and sides of the replaced circuit with epoxy. The epoxy bonds the new circuit to the base board material and insulates the circuit. (See Figure 5)
  16. Cure the epoxy per Procedure 2.7 Epoxy Mixing and Handling.

    Caution
    Some components may be sensitive to high temperature.
  17. Clean the board as required.
  18. Install new BGA per applicable procedures.
  19. Route and terminate the other end of the jumper wire.
Evaluation
  1. Visual examination for alignment and overlap of new circuit.
  2. Visual examination of epoxy coating for texture and color match.
  3. Electrical tests as applicable.
Procedure for reference only.
 

Related Products

115-1322 Circuit Bond Kit
Kit containing packages of clear, low viscosity, superior strength epoxy for circuit board damage repair.
201-3130 Circuit Track Kit
Kit to repair circuit board damage including lands and conductors.
Circuit Frames
Circuit Frames for surface mount pad, BGA pad and conductor repair.
115-4100 Bonding System
System designed to repair lifted and damaged conductors, pads, BGA pads, SMT pads.
Six Fast Fixes for Circuit Boards
Six Fast Fixes for Circuit Boards
Use this versatile kit to fix damaged SMT pads, lands, gold edge contacts, conductors, plated holes and base board. It's the total package.
Learn more ...
6 Common Mistakes of BGA Rework
6 Common Mistakes of BGA Rework
BGA rework is one of the most challenging rework procedures. Doing it right depends in large part on the skills and knowledge of the rework technician.
Learn more ...
Circuitry/PTH Repair on Multilayer PCBs
Circuitry/PTH Repair on Multilayer PCBs
Learn about services to repair severe damage to conductors and plated holes, including damaged holes in multilayer PCBs.
Learn more ...
Perfect Kit for Replating Gold Contacts
Perfect Kit for Replating Gold Contacts
There's simply no reason to scrap circuit boards when they have contacts contaminated with solder. Restore them using the Gold Contact Plating Kit.
Learn more ...
ipc-logo Circuit Technology Center has been an IPC member since 1986
Circuit Technology Center Logo
Surgeon grade rework and repair,
by the book and guaranteed. ®