First-Aid Kits for Circuit Boards ®
Newsletter | Ordering | Login
Phone: 978-373-1600
  

6.2.2 Jumper Wires, BGA Components, Through Board Method

  • Mill a hole through the board and insert a Teflon sleeve.
  • Insert a copper Circuit Track into the plated hole and Teflon sleeve.
  • Solder the Circuit Track to the plated hole connected to the BGA pad.
  • Overcoat the new connection with epoxy.
Outline
This method is used to add a jumper at a BGA site by running the jumper through a hole in the board. This method is normally used for engineering changes or modifications.

Note
This procedure requires precision milling equipment and highly trained technicians. This method is used when there is a buried via, and other methods of terminating to the opposite side are not an option.

Proprietary Information Proprietary
This guide may contain proprietary or copyright-protected information for access by authorized persons only.

Minimum Skill Level - Expert
Recommended for technicians with advanced soldering and component rework skills and extensive experience in most repair/rework procedures.

Conformance Level - High
This procedure most closely duplicates the physical characteristics of the original, and most probably complies with all the functional, environmental and serviceability factors.

Acceptability References
IPC-A-600 2.0 Externally Observable Characteristics  Proprietary
IPC-A-610 10.0 Discrete Wiring  Proprietary
Procedure References
1.0 Foreword
2.1 Handling Electronic Assemblies
2.2 Cleaning
2.5 Baking And Preheating
2.7 Epoxy Mixing and Handling
6.1 Jumper Wires
9.0 BGA Rework Procedures
Tools and Materials
CircuitMedic Part
Circuit Frames
Circuit Frames
CircuitMedic Part
Circuit Track Kit
Kit to repair circuit board damage including lands and conductors.
Cleaner
Cleaner
General purpose cleaner for removing contamination.
End Mills
End Mills
Designed for end cutting and hole boring.
CircuitMedic Part
Circuit Bond Packs
Clear, superior strength epoxy in two-compartment plastic packages
CircuitMedic Part
High Temp Tape Discs
High temperature polyimide tape discs, .50" diameter.
CircuitMedic Part
Knife with #16 Blades
A must-have tool for precise cutting, scraping and trimming.
Microscope
Microscope
Precision microscope with stand and lighting for work and inspection.
Milling Machine
Milling Machine
Use for precision milling of circuit board materials.
Oven
Oven
General purpose oven for drying, baking and curing epoxies.
Drill
Precision Drill
Precision drill press for accuracy and controlled depth drilling.
CircuitMedic Part
Scraper
Hardened stainless steel tip for scraping solder mask and removing defects.
Solderinmg Iron
Soldering Iron
Properly maintained soldering iron and properly sized soldering iron tips.
CircuitMedic Part
Tweezer, Point Tip
Fine point tweezers for precision work.
Wipes
Wipes
Nonabrasive, low-linting wipes for cleanup.
Images and Figures
6.2.2 Jumper Wires, BGA Components, Through Board Method
Figure 1: Mill a hole through the board and insert a Teflon sleeve.
6.2.2 Jumper Wires, BGA Components, Through Board Method
Figure 2: Insert a copper Circuit Track into the plated hole and Teflon sleeve.
6.2.2 Jumper Wires, BGA Components, Through Board Method
Figure 3: Solder the Circuit Track to the plated hole connected to the BGA pad.

6.2.2 Jumper Wires, BGA Components, Through Board Method
Figure 4: Overcoat the new connection with epoxy.
Procedure
  1. Clean the area.
  2. Remove the BGA component if installed, remove excess solder from the pads, and clean and inspect the site.
  3. Remove solder mask from the via pad terminating to the subject BGA pad. Do not remove any solder mask from the "dog bone" area.
  4. Mill a hole through the board at the precise coordinates using a Precision Drill System and End Mill of the appropriate size. (See Figure 1 and 5)

    Note
    Although both power and ground planes may be cut, inner layer signal traces must be avoided.
  5. Carefully inspect the milled hole and clean the area.
  6. Insert an appropriately sized Teflon sleeve into the milled hole. This sleeve will insulate the new conductor and prevent shorting to the inner layers. (See Figure 1)
  7. Select a Circuit Track to match the width of the circuit to be installed. Cut a length approximately as needed. The overlap solder connection should be a minimum of 2 times the circuit width.
  8. Gently abrade the top and bottom of the new Circuit Track with the buffer to remove any oxidation and clean.

    Note
    If needed, the ends of the Circuit Track may be tinned with solder prior to lap soldering in place.
  9. Insert one end of the Circuit Track into the plated hole connected to the BGA pad. Insert the opposite end through the Teflon sleeve. (See Figure 2)
  10. Apply a small amount of liquid flux and lap solder the Circuit Track to the plated hole connected to the BGA pad using solder and a soldering iron. Make sure the new circuit is properly aligned. (See Figure 3)
  11. Clean the area.
  12. Mix epoxy per procedure 2.7.
  13. Coat the top and sides of the new circuit with epoxy. The epoxy bonds the new circuit to the base board material and insulates the circuit. (See Figure 4)

    Note
    Keep the epoxy height below the BGA pad level.

    Caution
    Some components may be sensitive to high temperature.
  14. Clean the board as required.
  15. Install new BGA per applicable procedures.
  16. Solder a jumper wire to the exposed Circuit Track on the opposite side of the circuit board. Route and terminate the jumper wire as needed.
Evaluation
  1. Visual examination for alignment and overlap of new circuit.
  2. Visual examination of epoxy coating for texture and color match.
  3. Electrical tests as applicable.
Procedure for reference only.
 

Related Products

115-1322 Circuit Bond Kit
Kit containing packages of clear, low viscosity, superior strength epoxy for circuit board damage repair.
Circuit Frames
Circuit Frames for surface mount pad, BGA pad and conductor repair.
201-3130 Circuit Track Kit
Kit to repair circuit board damage including lands and conductors.
115-4100 Bonding System
System designed to repair lifted and damaged conductors, pads, BGA pads, SMT pads.
Questions?
Call 978-374-5000 or submit your question using the form below.

Your Name


Your Company


Your E-mail


Your Country


Your Phone


Questions



Do Your Repair Techs Deserve One?
Do Your Repair Techs Deserve One?
The Micro-Drill is the ideal tool for precision drilling, grinding and cutting on circuit boards. Use it to remove coatings, cuts circuits, drills holes, and much more.
Learn more ...
Discover 3 Options for BGA Rework
Discover 3 Options for BGA Rework
No matter how much we attempt to streamline and automate the process, BGA Rework has been, and will likely always be, a mixture of art and science.
Learn more ...
Must Have Circuit Boards First-aid Kits
Must Have Circuit Boards First-aid Kits
These kits have been used for decades by the most demanding electronics manufacturers. Every item is thoroughly field tested.
Learn more ...
Stop PCB Scrap Today
Stop PCB Scrap Today
What happens to your valuable circuit boards when they're damaged? Can they be repaired reliably and cost-effectively? Yes, if you have the skills and knowhow.
Learn more ...
ipc-logo Circuit Technology Center has been an IPC member since 1986
Circuit Technology Center Logo
Surgeon grade rework and repair,
by the book and guaranteed. ®