310-2100 Flextac Wire Dots
Special FREE Offer (See Form Below)
Flextac Wire Dots are a wire tacking system consisting of pre-cut shapes of a thin, flexible polymer film membrane coated on one side with a high performance, electronics grade permanent pressure sensitive adhesive resulting in a highly conformable, high strength bond. The adhesive release liner is an environmentally stable poly-coated kraft liner.
 |
Old - Jumper wires bonded with messy
and difficult to use quick set glue.
View Closup |
|
As with any wire tacking material, in order to achieve maximum bond strength and reliability, application surface must be clean, dry and free of flux, skin oils and other contaminants. Clean with isopropyl alcohol or equivalent if necessary. Firm application pressure develops better adhesive contact and thus improves bond strength. Avoid placing Flextac Wire Dots or any other wire tacking material directly over exposed copper or plated surfaces.
Flextac Wire Dots will perform best when applied at temperatures between 60�F (15�C) and 100�F (38�C). Do not apply below 50�F (10�C).
General Performance Characteristics
- Bond Strength
Flextac Wire Dots have very good initial bond strength that generally increases as a function of time over approximately 72 hours to stabilize as a high strength reliable bond.
- Humidity Resistance
High humidity has a minimal effect on adhesive performance. Bond strengths are actually slightly higher after exposure for 7 days at 90�F (32�C) and 90% relative humidity.
- Temperature Cycling and Bond Strength
 |
New - Jumper wires bonded with
neat, easy to use, Wire Dots.
View Closup |
|
Bond strength generally increases after four times through:
4 hours at 158�F (70�C)
4 hours at -20�F (-29�C)
16 hours at room temperature.
- Cleaning Process Resistance (chemical & hot water)
Flextac Wire Dots will hold securely after exposure to numerous chemicals including most flux cleaning solutions/sprays, saponifiers, "Freon" TF, mild acids and alkalis. Wires will hold securely through a typical PCB hot water wash.
- Temperature Range
Low: -40�F (-40�C)
High short term: 390�F (200�C)
High long term: 275�F (135�C)
- Repositioning
 |
| RoHS Compliant |
|
Flextac Wire Dots can be repositioned during and immediately after initial bonding without causing adhesive transfer or loss of bond strength.
- Shelf Life
Product retains its performance and properties for one year from date of purchase if properly stored at room temperature conditions. Storage in plastic bag is recommended.
- Applications
Jumper Wires
Conductor Repair, Surface Wire Method
 |
310-0651 Wire Dots, 6.5mm Round
Bonding 30 gauge jumper wire. |
|
 |
310-0652 Wire Dots, 6.5mm Square
Bonding 30 gauge jumper wire. |
|
 |
310-1001 Wire Dots, 10.0 mm Round
Bonding (3) 30 gauge jumper wires. |
|
 |
310-1002 Wire Dots, 10.0 mm Square
Bonding (3) 30 gauge jumper wires. |
|
| Physical and Thermal Properties |
| Property |
Typical Value |
Unit |
Test Method |
| Peel Strength 72 hrs @ 22�C |
84 |
0z./in. |
ASTM D3330 Modified |
| Static Shear Strength 72�F (22�C) / 1000g |
>10,000 |
min |
ASTM D3654 |
| Tensile Strength (Yield) 72�F (22�C) |
>2600 |
psi |
ASTM D2370 |
| Elongation |
100 |
% |
ASTM D2370 |
| Thermal Conductivity |
0.17 |
w/m-k |
ASTM C518 |
| Coefficient of Thermal Expansion |
5.5 x 10 -4 |
m/m/C |
ASTM D696 25-175C |
| Electrical Properties |
| Property |
Typical Value |
Unit |
Test Method |
| Dielectric Strength |
1700 |
volts/mil |
ASTM D149 |
| Dielectric Constant 25�C, 1 kHz |
3.4 |
------ |
ASTM D150 |
| Dissipation Factor 25�C, 1 kHz |
0.018 |
------ |
ASTM D150 |
| Surface Resistivity - Adhesive Layer |
>1 x 10 14 |
ohm/square |
ASTM D257 |
| Surface Resistivity - Polymer Film Layer |
>1 x 10 16 |
ohm/square |
ASTM D257 |
| Volume Resistivity - Adhesive Layer |
>1 x 10 15 |
ohm/cm |
ASTM D257 |
| Volume Resistivity - Polymer Film Layer |
>1 x 10 18 |
ohm/cm |
ASTM D257 |
| Insulation/Moisture Resistance - Adhesive Layer |
>1 x 10 11 |
ohm |
MIL-I-46058C (100 VDC 60 sec) |
| Insulation/Moisture Resistance - Polymer Film Layer |
>1 x 10 12 |
ohm |
MIL-I-46058C (100 VDC 60 sec) |
| Voltage Breakdown |
3500 |
volts |
------ |
Ordering Information
- Products may be ordered from distributors around the world. See our Distributor List.
- To order online click the "Add to Cart" button and follow the on screen instructions.
| Part No. |
Description |
Size |
Price |
Order |
| 310-2100 |
Flextac Wire Dots
Variety Pack |
All 4 Sizes |
$39.50 pkg/370 |
|
| 310-0651 |
Flextac Wire Dots
6.5 mm Round |
6.5 mm (.256 in.) Diameter |
$39.50 pkg/450 |
|
| 310-0652 |
Flextac Wire Dots
6.5 mm Square |
6.5 mm (.256 in.) Diameter |
$39.50 pkg/450 |
|
| 310-1001 |
Flextac Wire Dots
10.0 mm Round |
10.0 mm (.394 in.) Diameter |
$39.50 pkg/210 |
|
| 310-1002 |
Flextac Wire Dots
10.0 mm Square |
10.0 mm (.394 in.) Diameter |
$39.50 pkg/210 |
|
Freight, duties, and value added taxes may increase prices for products outside the US.
Web Page: http://www.circuitmedic.com/products/310-2100.shtml
CircuitMedic